Meyer Sound LEOPARD

Meyer Sound LEOPARD Specifications

ACOUSTICAL

• Operating Frequency Range: 55 Hz – 18 kHz

• Phase Response: 92 Hz – 18 kHz ±30 degrees

• Linear Peak SPL: 133.5 dB with 18 dB crest factor (M-noise), 130 dB (Pink noise), 134.5 dB (B‐noise)

COVERAGE

• Horizontal Coverage: 110°

• Vertical Coverage: Varies, depending on the array length and configuration

TRANSDUCERS

• Low Frequency: Two 9‐inch long‐excursion cone drivers; 2 Ω nominal impedance

• High Frequency: One 3‐inch diaphragm compression driver coupled to a constant‐directivity horn through a patented REM® manifold; 4 Ω nominal impedance

AUDIO INPUT

• Type: Differential, electronically balanced

• Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection

• Connectors: XLR 5‐pin female input with male loop output; XLR 3‐pin female connectors available to accommodate only balanced audio (no RMS signals)

• Input Impedance: 10 kΩ differential between pins 2 and 3

• Wiring:

  • Pin 1: Chassis/earth through 1 kΩ, 1000 pF, 15 V clamped network to provide virtual ground lift at audio frequencies

  • Pin 2: Signal +

  • Pin 3: Signal ‐

  • Pin 4: RMS (polarity insensitive)

  • Pin 5: RMS (polarity insensitive)

  • Case: Earth ground and chassis

• Nominal Input Sensitivity: 6.0 dBV (2.0 V rms) continuous is typically the onset of limiting for noise and music

• Input Level: Audio source must be capable of producing +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker

AMPLIFIERS

• Type: 3‐channel, open‐loop, class D

• Total Output Power: 3900 W peak

• THD, IM, TIM: < 0.02%

• Cooling: Convection

AC POWER

• Connector: powerCON 20 input with loop output

• Automatic Voltage Selection: 90–265 V AC

• Safety Rated Volted Range: 100–240 V AC, 50–60 Hz

• Turn-on and Turn-off Points: 90 V AC turn‐on, no turn‐off; internal fuse‐protection above 265 V AC

CURRENT DRAW:

• Idle Current: 0.46 A rms (115 V AC); 0.35 A rms (230 V AC); 0.49 A rms (100 V AC)

• Max Long‐Term Continuous Current (>10 sec): 3.0 A rms (115 V AC); 1.5 A rms (230 V AC); 3.4 A rms (100 V AC)

• Burst Current (<1 sec): 4.4 A rms (115 V AC); 2.3 A rms (230 V AC) 5.5 A rms (100 V AC)

• Maximum Instantaneous Peak Current: 12.6 A peak (115 V AC); 6.3 A peak (230 V AC); 14.5 A peak (100 V AC)

• Inrush Current: < 20 A peak

RMS NETWORK

• Equipped with two‐conductor, twisted‐pair network; reports all amplifier operating parameters to host computers

PHYSICAL

• Dimensions: W: 26.93 in (684 mm) x H: 11.11 in (282 mm) x D: 21.66 in (550 mm)

• Weight: 75 lbs (34.0 kg)

• Enclosure: Premium multi‐ply birch, slightly textured black finish

• Protective Grille: Powder‐coated, hex‐stamped steel with acoustical black mesh

• Rigging: End frames with captive GuideALinks secured with 0.3125 in x 0.63 in quick‐release pins that allow 0.5° to 15° splay angles; detachable side and rear handles

MANUFACTURER NOTES

1. See the Galileo GALAXY Network Platform User Guide for more details.

2. Loudspeaker system predictions for coverage and SPL are available in Meyer Sound’s MAPP System Design Tool.

3. Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics.

4. Linear Peak SPL is measured in free‐field at 4 m referred to 1 m. Loudspeaker SPL compression measured with M‐noise at the onset of limiting, 2‐hour duration, and 50 °C ambient temperature is <2 dB. M-noise is a full bandwidth, (10 Hz–22.5 kHz) test signal developed by Meyer Sound to better measure the loudspeaker’s music performance. It has a constant instantaneous peak level in octave bands, a crest factor that increases with frequency, and a full bandwidth Peak to RMS ratio of 18 dB. Pink noise is a full bandwidth test signal with Peak to RMS ratio of 12.5 dB.B-noise is a Meyer Sound test signal used to ensure measurements reflect system behavior when reproducing the most common input spectrum, and to verify there is still headroom over pink noise.

5. Pins 4 and 5 (RMS) only included with XLR 5‐pin connector that accommodates both balanced audio and RMS signals.

6. Peak power based on the maximum unclipped peak voltage the amplifier will produce into the nominal load impedance.

7. AC power cabling must be of sufficient gauge so that under burst current rms conditions, cable transmission losses do not cause the loudspeaker’s voltage to drop below the specified operating range.

IMPORTANT: CMG strive to provide the most accurate and complete equipment description and item specifications, including weight, rigging, power requirements and recommended use. All product information has been sourced from the original equipment manufacturer (or Australian distributor) and is based on the manufacturers standard specifications. Actual specifications for this equipment may differ. It is highly recommended that all equipment details are confirmed with our team PRIOR TO USE as the supplier, as the latter (CMG Audio Visual Pty Ltd) cannot be held accountable for any inaccuracies.